How to Replace a Kia Sportage Replacement Key

The key in many Kia models has an electronic keyless entry system built into. This key is similar to an remote control and can be exchanged by an Kia dealer.

Key fobs might stop working due to a variety of reasons, including the battery of the coin is dead, worn buttons or buttons, signal interference, water damage and a faulty receiver module. Here are some helpful tips on how to get your kia sportage replacement key (visit my webpage) working again.

How do you replace the remote key or smartkey?

It doesn't matter if your 2006 kia sportage key fob comes with an intelligent key, remote key push to start key, or regular metal non-transponder key, the battery in these keys will eventually need replacing. This is especially when the vehicle displays a message that indicates that the remote or smart key is not powered by the battery.

Luckily, this is a relatively simple process. To replace the battery on the keyfob remove your mechanical key from the slot at the back of the fob. Then, push the cover off. Inside the key fob there will be an incredibly small screw that holds the battery in place. Utilizing a small screwdriver remove the screw and pull out the battery that was in place. Then, you can insert the new battery and close the hole in the key fob.

Once the key fob has an updated battery and you've tested it, press the locks and unlock buttons. If the doors unlock and lock according to your expectations, then you're all set! You can now use Kia's hands-free lock/unlock function when your fingers start to get cold or you have to do some errands in Brandon.

Note: Some key fobs may need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If your key requires to be reprogrammed, you will need to be aware of the key code number that is stamped on the tag that identifies the key and then record it in a safe location.

How do you replace the battery?

If the Kia key fob doesn't respond when you press the lock/unlock button, it is likely that the battery is depleted. A low battery could cause other problems like the check engine light turning on or a delay in cranking the engine. It is quite simple to replace key fob batteries by using only the use of a few tools.

Before beginning the process be sure that your vehicle is off and that all doors are closed. Find the small, metal or plastic piece near the bottom of the key fob. Move it until the key falls out. The key can be inserted into the driver door handle to unlock your car.

To replace the battery in the key fob, remove the rear cover. Make use of a plastic pry tool to open the latch that holds the black negative cable. Remove the old battery and then position the new battery in a way that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or bending the metal contacts.

After installing the new battery, turn the key fob on and off in the ignition until the door locks up. Then, test your Kia key fob and see if it is working properly again.

How to replace the smart key

You could have a standard keyfob or a Smart Key depending on the model of 2013 kia optima key replacement Sportage. The smart key has an embedded mechanical key blade, however, the standard key fob does not. Both key fobs contain an internal battery that will eventually require changing. It is a simple process which takes just two minutes.

Make sure to shut off your Kia and be on a level well-lit and well-lit area before you begin. Keep in mind that there are tiny pieces inside the fob that could be snagged if not vigilant.

The first step is to find the small release button that is located on the lower backside of your fob. It will be either an oval silver button or a rectangular slot. When you press it the mechanical key blade will be released and you will be able to open the key fob.

Once you have the key fob opened it is easy to remove the old battery, and replace it. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. When you are done, you should be able to lock or unlock your car with your key fob, even if your engine isn't running!

How do I replace a mechanical key

The 2012 kia sportage key fob programming key fob is a fantastic feature that lets us lock and unlock our vehicle with the click of the button. Like any other device it may have issues at times. There are solutions to resolve these issues and keep your key fobs working for many years.

One of the most frequent problems is a weak or dead battery. The battery could cause the device to stop working or operate intermittently. If this happens, try replacing the battery with a new one.

If this doesn't resolve the issue, try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. After the battery has been removed and replaced with a new one.

Close and open the door using the mechanical key. (Every kia lost keys fob comes with a spare mechanical key that fits into the slot). Test the key fob to ensure that it's working correctly. Contact a dealer or a locksmith to fix the issue when the fob still is not working. To avoid locking outs in the future, ensure that you have an emergency key that will work in all of the trunk and door cylinders.