How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models has a keyless entry system built into. This key usually resembles an remote control, and can be exchanged by a new one purchased from an Kia dealer or a locksmith.

Key fobs might stop working due to a number of reasons, including an inactive battery, worn out buttons, signal interference or water damage. Here are some tips to help you get your Kia sportage replacement key working again.

How do you replace a remote key or a smartkey?

The battery inside your kia ceed key fob's smart key will eventually have to be replaced, regardless of whether it's a remote key that starts with a push button or a normal metal key that is not equipped with transponder. This is especially in the event that your vehicle displays a message that indicates that the smart or remote key has low battery power.

It's quite simple to do. To replace the keyfob battery, remove your mechanical key from the slot at the back of the fob. Then, pull the cover open. A small screw will be found inside the key fob that holds the battery in the correct position. Take out the old battery by detaching the screw with a small screwdriver. Insert the new battery and then close the gap on the key fob.

When the key fob is equipped with new batteries check it by pressing the locks and unlock buttons. If the doors unlock and lock as expected, then you're good to go! You can now utilize your Kia's hands-free lock/unlock feature whenever your fingers feel cold or you have to make errands in Brandon.

Note: Certain key fobs might need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If your key requires to be programmed again, you will need to be aware of the key code written on the tag that identifies the key and then record it in a safe location.

How to replace the battery

If the Kia key fob doesn't respond to pressing the lock or unlock button, it's a sign that the battery is depleted. A battery that is not functioning properly can cause other issues, like the check engine light flashing or the engine not working correctly. It is relatively easy to replace the key fob batteries using just the use of a few tools.

Make sure to shut off your vehicle and shut all doors before you begin. Find the small metal or plastic piece near the bottom of the key fob. Then, jiggle it until the metal key falls out. You can then insert the key in the handle of the door for the driver to open your car.

To replace the key fob's battery, take off the rear cover and use a plastic pry bar tool to release the latch holding the black negative battery cable. Remove the old battery, and then align the replacement battery to ensure its "+" side faces you and the "-", negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

Once the new battery is installed, turn the key fob off and on in the ignition for a few times until the door locks cycle. Then you can test your Kia key fob to determine if it is working properly again.

How do you replace the smart key

There is a possibility of having a standard keyfob or a Smart Key depending on the model of Kia Sportage. The difference is that the smart fob has a small mechanical key blade in it, whereas the standard fob isn't equipped with. Both types of key fobs have an internal battery which eventually needs to be replaced. This is an easy process that takes only two minutes.

Before you start before you begin, make sure that you are on a flat surface with sufficient lighting and that your kia sportage key is not on. Be aware that the fob can contain tiny parts that could fall should you not be careful.

The small release button is located on the lower backside. It's either a circular button or rectangular slot. When you press it, the mechanical key blade will appear and you can then open the key fob.

After the key fob has been open, remove the old battery. The new battery is CR-2032, and can be purchased online or in your local auto parts store. After you've finished, you should be able to lock or unlock your vehicle using your key fob even if the engine isn't running!

How to replace the mechanical key

The kia keys made key fob is a wonderful convenience that allows us to lock and unlock our car with the press of an button. However, like all devices there are issues with it occasionally. Luckily, there are steps that can be taken to troubleshoot these issues and keep our key fobs in good working order for the long run.

A low or dead battery is one of the most frequent problems. This can cause the fob to stop working entirely or even to stop working intermittently. If this is the case you should replace the battery a new one.

If this isn't enough to solve the issue, use a standard flathead screwdriver to push the fob's plastic casing open. Be cautious not to damage any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a new one.

Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob to verify that it's functioning correctly. Contact a dealer or a locksmith to address the issue if the fob is still not working. Make sure they cut you an emergency key that functions in all the trunk and door cylinders, to prevent lockouts in the future.