Reasons Your fiat key cover 500 Key Fob Won't Work

A key fob for the fiat key fob replacement 500 is a convenient method to unlock the doors and get started the car. There are a myriad of reasons the fob could stop working. This could be due to a dead coin battery damaged receiver module, water damage issues, and interference.

This listing is for a NEW replacement fiat punto key programming Flip Key Remote - look-alike Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not functioning. Modern key fobs only have an operating range that is limited and must be within a few inches of the vehicle to function. If you are far from your car and hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the coin cell battery (Part number CR2032) with a new one from a trusted brand like Panasonic, Duracell, or Energizer. They are usually available at your local hardware store, or online.

You can test the coin-cell battery by pressing the buttons while standing close to your fiat 500 key cover uk 500. The parking lights will flash and the key fob should operate the lock and unlock switches.

If your fob's key isn't working after replacing the battery, there could be water damage that prevents it from communicating with the module inside your vehicle. Water damage can happen in a number of ways, from an accidental splash to submerging the fob salt water at the beach. If you believe your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this isn't working, you'll have to get your fob reset by an auto locksmith or dealer.

Water Damage

Although the fob is equipped with rubber seals to keep water out of the chip's electronic circuit, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the circuit board of the fob, causing it to short out and eventually die. It's not the best idea to get the fob wet, but don't give it up if you accidentally drop it in water or fail to take it out of your pants pocket.

Remove the battery first. Before replacing the battery, clean the electronic chip using isopropyl, or a similar product. Then try the fob and verify if it is working. If the key doesn't work, it may have to be programmed again. This is usually handled by a dealer or professional auto locksmith.

If your key is old and is not programmed for your vehicle then you'll need to replace it completely. A professional locksmith for cars can complete this simple process. The locksmith will need the key cut to match the car's ignition. The locksmith will also have to program your fob into the vehicle's system. This is a cheap and quick process that could be completed within the same day.

Receiver Module Issues

One of the main reasons your 500 key fob might stop functioning is that it's out of range. The remote's range is of 30 feet, which means should you be too far from your car, it won't respond to your commands. It's easy to solve this issue by moving the remote closer to your car until it responds.

If you've replaced the battery on your coin (commonly called"button" or "button" or "watch") and your fob still won't work it could be due to an internal circuit board issue. Reprogramming the fob is usually the solution to the issue. There are instructions on how to do this for all automobiles by searching YouTube or checking out the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in the correct position. If they lose tension, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances, the fob might be out of sync with your vehicle because of hardware or software problems. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases, they may need to reinstall the program in your body control module as well.

Interference

In addition to a dead battery on a coin the key fob could not be able to receive or transmit the signal due to interference. This could happen when the key fob is in close proximity to a radio transmitter like a cell phone or radar detector. Other reasons why the key fob could not function may be a lack of connection to the buttons and internal chip, or water damage.

If your key fob suddenly stopped working, or if you've tried everything at home to resolve it (e.g. You could have a malfunctioning 500 receiver module if you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset every single system on board in your 500 device, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and allow you to restart the computer in your car. This can help get your key fob working again. If the problem persists you should seek the advice of an expert technician. They will be able diagnose the exact cause of any problems.