Fiat 500 Replacement Key Fob

If your remote key fob isn't working, it might be time to replace the battery. If you replace the battery and it isn't working, the problem may be elsewhere.

At United Locksmith, we specialize in the creation of new keys for old automobiles. We have all the tools and accessories needed for this type of service.

Dead Coin Battery

A dead battery is the most common cause of your fiat replacement key fob 500 keyfob not locking or unlocking the doors. The key fob contains an in-built battery that is prone to draining quickly if it is not frequently used. If your remote started to show signs of weakening such as a loss in range, and then stopped working completely The battery is probably dead.

The battery inside the key fob is held in place by metal clips that hold it in place. If the clips are loose they can cause contact issues which will prevent your remote from receiving power. Use a flathead screwdriver to pry open the retaining clip and remove the battery. Be sure to use an alternative battery that has the same kind of voltage, the same size, and specification as the original battery.

The key fob could also be damaged or corroded by exposure to water. Even a quick bath in warm, soapy water can cause damage to the chip. Keep your key fob dry.

Water Damage

If your key fob isn't working correctly, it could be caused by water damage. The rubber seals on key fobs keep them from getting damaged by a slight drizzle or splash of water. However, it is crucial to keep your keys from the ocean, washing machine, and even the pool.

The key fob contains an electronic chip that transmits an alert to the immobilizer system in your car. This is what allows your 500 to lock or start, but if the chip gets wet, it can no longer function.

You can try cleaning the inside electronics of your keyfob with isopropyl Alcohol or an electronic cleaner to see if they are still good. It is best to replace a key fob in the event that it's submerged into salt water instead of trying to repair it yourself.

While a replacement fob can cost you a little bit of money, it's a lot cheaper than paying for your fiat 500 key fob reset 500 to be towed to the dealer and repaired! Plus, you can make it yourself in just a few easy steps. Be sure to use the correct type of battery before you attempt to open your key fob. You can find step-bystep directions for every car keyfob online.

Faulty Chip

The chip that is contained in the key fob communicates with your car's immobiliser unit to make sure the vehicle is capable of starting when the correct key is inserted. If the chip is damaged or destroyed, your car won't start, no matter what you do.

Damage to the water or a dead battery are the most frequent causes of the chip being damaged. It is best to hand over the work to a professional locksmith who can replace the chip quickly and at reasonable cost.

If your key fob stops functioning after exposure to clean tap water or rain, remove the battery and wipe down the electronic component using a paper towel to ensure that it is completely dry before putting it back into. If the key fob will not work, there's the possibility that it has malfunctioning components and need to be replaced.

Some people will turn to their dealer when they are in need of a new Fiat key fob, but this can be a very costly option. United Locksmith is the best option for you if would like to have your Fiat key fob replaced at a reasonable price. We have the equipment and know-how needed to repair your fiat car keys key fob in a quick and professional manner.

Faulty Receiver Module

Fiat key fobs transmit a signal to the vehicle that can unlock and close doors (and start the car for vehicles with an automatic transmission) up to 50 feet. There are several reasons why the fob might stop working. This could be due to a dead battery, water damage, worn-out buttons, a receiver issue, signal interference or malfunctioning chips.

If the fob was located in the pocket that has been subject to extreme trauma (such as being dropped onto the hard floor or washed in the washer), it may not be able to connect with the Body Control Module (BCM) of the car. This is because the BCM is an extremely secure system that will only accept a signal from a genuine original key and not any other.

You will need to replace the fob in case this happens. A professional locksmith can take care of all aspects of the key replacement procedure, including programming a new one for your 500. They can even provide you with the fob cloned to work the same as the original (and costs just less than what it would cost).