Reasons Your fiat panda remote key replacement 500 Key Fob Won't Work

A key fob from Fiat 500 makes it simple to open doors and start your vehicle. There are many reasons the fob could stop working. This could be due to a dead coin-battery and water damage, as well as problems with the receiver modules, and interference.

This listing is for a NEW replacement fiat 500 key fob programming Panda key programming, dy-cos.Com, Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to search for local automotive locksmiths). Includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob doesn't function is a dead battery. Modern key fobs have limited operating range and must be within a few inches of your vehicle to function. If you're far away from your vehicle, and you press the key fob button the car won't respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this occurs you need to replace the battery of your coin-cell (Part Number CR2032) by a brand new one of a reliable brand, like Panasonic Duracell or Energizer. You can typically find them in your local hardware store, or online.

After you've replaced the coin cell battery, you can test it by standing next to your fiat 500 spare key cost uk 500 and pressing the buttons. The car should flash its parking lights, and the key fob will operate the lock and unlock buttons.

If your key fob still isn't working after replacing the battery, there might be water damage that has prevented it from communicating with the module in your vehicle. Water damage can happen in a variety of ways, from small splashes to submerging the fob in salt water at the beach. If you suspect that your fob has been exposed to water, try putting it in a dry rice bag to draw the moisture back out. If that doesn't work your fob may need to be reset by an experienced auto locksmith or by the dealer.

Water Damage

Water damage can occur if you immerse the fob into the ocean, or wash it in a washing machine. Saltwater can be particularly harmful to the fob's circuit board that can cause it to short out and eventually end up dying. It's not the best idea to submerge the fob in water but don't give up in the event that you accidentally drop it in water, or fail to take it out of your pocket.

First take the battery off the fob. Clean the electronic chip with isopropyl or a similar product and dry it thoroughly before replacing the battery. Then try the fob and test if it works. If the key isn't working it could need to be reset. This is usually done by an auto locksmith or dealer.

If the key you have is older and is not programmed to work with your vehicle, you will need to replace it completely. A professional locksmith in the automotive industry can do this job. The locksmith needs to cut the key to match the ignition on your vehicle. The locksmith also needs to reprogram the fob into the car's system. This is a cheap and fast process that can be completed in the same day.

Receiver Module Issues

The 500 key fob you have may be inoperable because it's out of range. The remote usually has an operating range of 30 feet or less and if it's far away from your car it will not respond to your commands. It is possible to fix this by moving the remote closer to your car until it responds.

If your fob doesn't work after you replace the coin battery, also called a "button", "watch" or "button" it could be due to a problem with the internal circuit board. In most cases, reprogramming the fob will resolve this issue. The instructions are available for most vehicles on YouTube or in the owner's manual.

You may have to replace the metal retaining clips that hold the coin battery in place. If they loose tension they could stop the coin battery from being seated properly and can cause the remote to malfunction.

In rare instances, the fob can become out of alignment with your vehicle because of hardware or software problems. This could be a huge issue, but you are able to usually fix it by visiting a local dealer or auto locksmith to reprogram your fob for you. In some cases they may have to reinstall the software in your body control module too.

Interference

Interference can also cause the key fob to be unable to receive or transmit an signal. This could happen when the keyfob is located in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons why the key fob could not function include a poor connection to the buttons and internal chip or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to fix it (e.g. You may have a faulty 500 receiver module if you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then processed by the vehicle.

There's a simple method to reset the 500's internal system including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then, reconnect the battery. This will eliminate any residual electricity and restart the car's computer system, which can help you the key fob to function again. If the problem persists you should consult an expert technician. They will be able to determine the exact cause of any issues.